Cork has been one of the main pillars of the Portuguese economy for some decades and is today one of the most important natural materials exported from Portugal to the world. Nowadays, cork composites are used in products as diverse as sports flooring, wall memos, ladies’ bags and shoes. However, these composites need to be processed and one of the first steps to produce cork granules is their grinding process. Although cork has a relatively low mechanical resistance and hardness, the degree of abrasion generated by cork on grinding pads during the grinding process is considerable. This study aims to determine which type of wear mechanisms are strongly associated with the premature end of life of grinding pads, which occurs due to reduced cutting efficiency and the generation of cork granules outside the specifications. This study will allow to understand the best ways to extend the useful life of tools and improving the cost/benefit ratio. The results obtained led to an understanding of the phenomena induced in the inserts and generated promising alternative solutions using special materials and coatings, allowing to improve the behaviour of the inserts against wear, making this operation more efficient and profitable.
- Open Access
- Article
A Review of Wear Mechanisms and Solutions Regarding Inserts for Grinding Applications
- Naiara Poli Veneziani Sebbe 1, 2, *,
- Andresa Baptista 1, 3,
- Gustavo Pinto 1, 3,
- Iván Iglesias 4,
- Emanuel Thiago Oliveira 1
Author Information
Received: 15 Jul 2025 | Revised: 30 Sep 2025 | Accepted: 09 Oct 2025 | Published: 05 Jan 2026
Abstract
Keywords
cork | cork grinders | grinders inserts | inserts wear | wear mechanisms | abrasion
References
- 1.
Gil, L. Cork Composites: A Review. Materials 2009, 2, 776–789. https://doi.org/10.3390/ma2030776.
- 2.
Gil, L. New Cork-Based Materials and Applications. Materials 2015, 8, 625–637. https://doi.org/10.3390/ma8020625.
- 3.
Gil, L. Cork: A strategic material. Front. Chem. 2014, 2, 16. https://doi.org/10.3389/fchem.2014.00016.
- 4.
Santos, T.; Amaral, J.S.; Amaral, V.S.; et al. In-plane thermal anisotropy of natural cork and its variability. Measurement 2025, 242, 116062. https://doi.org/10.1016/j.measurement.2024.116062.
- 5.
Lakreb, N.; Şen, U.; Toussaint, E.; et al. Physical properties and thermal conductivity of cork-based sandwich panels for building insulation. Constr. Build. Mater. 2023, 368, 130420. https://doi.org/10.1016/j.conbuildmat.2023.130420.
- 6.
Gerometta, M.; Gabrion, X.; Lagorce, A.; et al. Towards better understanding of the strain–stress curve of cork: A structure–mechanical properties approach. Mater. Des. 2023, 235, 112376. https://doi.org/10.1016/j.matdes.2023.112376.
- 7.
Paulo, J.A.; Santos, D.I. Virgin cork colour and porosity as predictors for secondary cork industrial quality. Ind. Crops Prod. 2023, 205, 117513. https://doi.org/10.1016/j.indcrop.2023.117513.
- 8.
Anjos, O.; Pereira, H.; Rosa, M.E. Effect of quality, porosity and density on the compression properties of cork. Holz Als Roh-Und Werkst. 2008, 66, 295–301. https://doi.org/10.1007/s00107-008-0248-2.
- 9.
Silva, S.P.; Sabino, M.A.; Fernandes, E.M.; et al. Cork: Properties, capabilities and applications. Int. Mater. Rev. 2005, 50, 345–365. https://doi.org/10.1179/174328005X41168.
- 10.
Oliveira, V.; Pereira, H. Cork and Cork Stoppers: Quality and Performance. In Chemistry and Biochemistry of Winemaking, Wine Stabilization and Aging; IntechOpen: London, UK, 2021. https://doi.org/10.5772/intechopen.92561.
- 11.
Fonseca, A.P.; Adame, C.F.; Teodoro, O.M.N.D. The role of coatings on the sealing of cork stoppers. J. Food Eng. 2024, 378, 112114. https://doi.org/10.1016/j.jfoodeng.2024.112114.
- 12.
Suffo, M.; Pérez-Muñoz, C.; Alba, G.; et al. An Innovative Polypropylene/Waste Cork Composite Material for Spirit and Wine Stopper Caps. Appl. Sci. 2024, 14, 3014. https://doi.org/10.3390/app14073014.
- 13.
Castro, O.; Silva, J.M.; Devezas, T.; et al. Cork agglomerates as an ideal core material in lightweight structures. Mater. Des. 2010, 31, 425–432. https://doi.org/10.1016/j.matdes.2009.05.039.
- 14.
Gil, L. Cork. In Materials for Construction and Civil Engineering; Springer International Publishing: Cham, Switzerland, 2015; pp. 585–627. https://doi.org/10.1007/978-3-319-08236-3_13.
- 15.
Pinto, C.; Cravo, S.; Mota, S.; et al. Cork by-products as a sustainable source of potential antioxidants. Sustain. Chem. Pharm. 2023, 36, 101252. https://doi.org/10.1016/j.scp.2023.101252.
- 16.
Reculusa, S.; Trinquecoste, M.; Dariol, L.; et al. Formation of low-density carbon materials through thermal degradation of a cork-based composite. Carbon 2006, 44, 1316–1320. https://doi.org/10.1016/j.carbon.2005.12.051.
- 17.
Pintor, A.M.A.; Ferreira, C.I.A.; Pereira, J.C.; et al. Use of cork powder and granules for the adsorption of pollutants: A review. Water Res. 2012, 46, 3152–3166. https://doi.org/10.1016/j.watres.2012.03.048.
- 18.
Saadallah, Y.; Zemour, I.; Boulemnakher, F. Experimental investigation of mechanical behavior of agglomerated cork. Mater. Des. Process. Commun. 2020, 2, e123.
- 19.
Vaz, M.F.; Fortes, M.A. Friction properties of cork. J. Mater. Sci. 1998, 33, 2087–2093. https://doi.org/10.1023/A:1004315118535.
- 20.
Martínez-Martínez, D.; Tiss, B.; Glanzmann, L.N.; et al. Protective films on complex substrates of thermoplastic and cellular elastomers: Prospective applications to rubber, nylon and cork. Surf. Coat. Technol. 2022, 442, 128405. https://doi.org/10.1016/j.surfcoat.2022.128405.
- 21.
Fang, X.D.; Yao, Y.; Arndt, G. Monitoring groove wear development in cutting tools via stochastic modelling of three-dimensional vibrations. Wear 1991, 151, 143–156. https://doi.org/10.1016/0043-1648(91)90354-W.
- 22.
Liu, Z.Q.; Ai, X.; Zhang, H.; et al. Wear patterns and mechanisms of cutting tools in high-speed face milling. J. Mater. Process. Technol. 2002, 129, 222–226. https://doi.org/10.1016/S0924-0136(02)00605-2.
- 23.
Shen, Z.; Lu, L.; Sun, J.; et al. Wear patterns and wear mechanisms of cutting tools used during the manufacturing of chopped carbon fiber. Int. J. Mach. Tools Manuf. 2015, 97, 1–10. https://doi.org/10.1016/j.ijmachtools.2015.06.008.
- 24.
Yan, G.; Yue, W.; Meng, D.; et al. Wear performances and mechanisms of ultrahard polycrystalline diamond composite material grinded against granite. Int. J. Refract. Met. Hard Mater. 2016, 54, 46–53. https://doi.org/10.1016/j.ijrmhm.2015.07.014.
- 25.
Fan, S.; Zhang, L.; Cheng, L.; et al. Wear mechanisms of the C/SiC brake materials. Tribol. Int. 2011, 44, 25–28. https://doi.org/10.1016/j.triboint.2010.09.003.
- 26.
Maranho, O.; Rodrigues, D.; Boccalini, M.; et al. Mass loss and wear mechanisms of HVOF-sprayed multi-component white cast iron coatings. Wear 2012, 274, 162–167. https://doi.org/10.1016/j.wear.2011.08.024.
- 27.
Behera, B.C.; Ghosh, S.; Rao, P.V. Wear behavior of PVD TiN coated carbide inserts during machining of Nimonic 90 and Ti6Al4V superalloys under dry and MQL conditions. Ceram. Int. 2016, 42, 14873–14885. https://doi.org/10.1016/j.ceramint.2016.06.124.
- 28.
ISO 14577-1:2015; Metallic Materials—Instrumented Indentation Test for Hardness and Materials Parameters. Part 1: Test Method. ISO: Geneva, Switzerland, 2015.
- 29.
Dzhemelinskyi, V.; Hruska, M.; Mordyuk, B.; et al. Surface Hardness Improvement of AISI D2 Tool Steel by Laser Transformation Hardening Process Using High-Power Disk Laser. In Advances in Design, Simulation and Manufacturing VII; Springer: Cham, Switzerland, 2024; pp. 178–187. https://doi.org/10.1007/978-3-031-61797-3_15.
- 30.
Yazıcı, A. Wear on steel tillage tools: A review of material, soil and dynamic conditions. Soil Tillage Res. 2024, 242, 106161. https://doi.org/10.1016/j.still.2024.106161.
- 31.
Luyckx, S.; Sacks, N.; Love, A. Increasing the abrasion resistance without decreasing the toughness of WC–Co of a wide range of compositions and grain sizes. Int. J. Refract. Met. Hard Mater. 2007, 25, 57–61. https://doi.org/10.1016/j.ijrmhm.2005.11.015.
- 32.
Gant, A.J.; Gee, M.G. Abrasion of tungsten carbide hardmetals using hard counterfaces. Int. J. Refract. Met. Hard Mater. 2006, 24, 189–198. https://doi.org/10.1016/j.ijrmhm.2005.05.007.
- 33.
Gee, M.G.; Gant, A.; Roebuck, B. Wear mechanisms in abrasion and erosion of WC/Co and related hardmetals. Wear 2007, 263, 137–148. https://doi.org/10.1016/j.wear.2006.12.046.
- 34.
Angseryd, J.; From, A.; Wallin, J.; et al. On a wear test for rock drill inserts. Wear 2013, 301, 109–115. https://doi.org/10.1016/j.wear.2012.10.023.
- 35.
Grasser, D.; Gallo, S.C.; Pereira, M.; et al. Experimental investigation of the effect of insert spacing on abrasion wear resistance of a composite. Wear 2022, 494, 204277. https://doi.org/10.1016/j.wear.2022.204277.
- 36.
Toller-Nordström, L.; Sten, S.; Kritikos, M.; et al. Wear properties of cemented carbides with new binder solutions for rock drilling inserts. Wear 2025, 570, 205909. https://doi.org/10.1016/j.wear.2025.205909.
- 37.
Grejtak, T.; Kuns, M.W.; Lacey, J.A.; et al. Enhancing the shredder durability for biomass preprocessing by utilizing wear-resistant cutter materials. Tribol. Int. 2025, 210, 110766. https://doi.org/10.1016/j.triboint.2025.110766.
- 38.
Saai, A.; Bjørge, R.; Dahl, F.; et al. Adaptation of Laboratory tests for the assessment of wear resistance of drill-bit inserts for rotary-percussive drilling of hard rocks. Wear 2020, 456, 203366. https://doi.org/10.1016/j.wear.2020.203366.
- 39.
Tkalich, D.; Kane, A.; Saai, A.; et al. Wear of cemented tungsten carbide percussive drill–bit inserts: Laboratory and field study. Wear 2017, 386, 106–117. https://doi.org/10.1016/j.wear.2017.05.010.
This work is licensed under a Creative Commons Attribution 4.0 International License.
Suite 4002 Level 4, 447 Collins Street, Melbourne, Victoria 3000, Australia
General Inquiries: info@sciltp.com