Waste heat recovery is a key strategy for improving the energy efficiency and sustainability of metallurgical processes, in which substantial energy is lost through high-temperature exhaust gases. This study numerically investigates an aluminum-block preheating chamber designed to recover thermal energy from furnace exhaust streams. A three dimensional computational fluid dynamics model was developed to simulate turbulent gas flow and conjugate heat transfer between the exhaust gases and solid aluminum blocks. Two geometric configurations, based on half- and full-block arrangements, and two operating conditions, with the extractor hood open or closed, were compared in terms of flow patterns, temperature distributions, and heat recovery performance. The results demonstrate that both operating conditions and block geometry strongly influence the system’s thermal behavior. Enhanced flow mixing promotes heat transfer, while the full-block configuration increases overall thermal energy absorption through greater interaction with the hot gas stream. The optimal configuration produces a substantial increase in block temperature and recovered energy. An economic assessment based on industrial production data estimates annual natural gas savings worth approximately €25,000.
- Open Access
- Article
Thermal Performance of a Preheating Chamber for Convective Heating of Aluminum Blocks
Author Information
Received: 05 June 2026 | Revised: 16 October 2026 | Accepted: 20 October 2026 | Published: 29 October 2026
Abstract
Keywords
CFD analysis | waste heat recovery | energy efficiency | preheating | aluminum industry
References
- 1.
Menzie, W.D.; Barry, J.J.; Bleiwas, D.I.; et al. The Global Flow of Aluminum from 2006 through 2025; Open-File Report 2010–1256; U.S. Geological Survey: Reston, VA, USA, 2010; pp. 1–60. https://doi.org/10.3133/ofr20101256.
- 2.
Das, S. Achieving Carbon Neutrality in the Global Aluminum Industry. JOM 2012, 64, 285–290. https://doi.org/10.1007/s11837-012-0237-0.
- 3.
Luo, Z.; Soria, A. Prospective Study of the World Aluminium Industry; EUR 22951 EN; Publications Office of the European Union: Luxembourg, 2008. https://doi.org/10.2791/36024.
- 4.
Steinfeld, A. High-Temperature Solar Thermochemistry for CO2 Mitigation in the Extractive Metallurgical Industry. Energy 1997, 22, 311–316. https://doi.org/10.1016/s0360-5442(96)00103-x.
- 5.
Raabe, D.; Ponge, D.; Uggowitzer, P.J.; et al. Making Sustainable Aluminum by Recycling Scrap: The Science of “Dirty” Alloys. Prog. Mater. Sci. 2022, 128, 100947. https://doi.org/10.1016/j.pmatsci.2022.100947.
- 6.
Dardor, D.; Flórez-Orrego, D.; Germanier, R.; et al. Decarbonizing the Aluminium Industry: A Comprehensive Review of Pathways and Process Integration Perspectives. Energy Strategy Rev. 2025, 61, 101853. https://doi.org/10.1016/j.esr.2025.101853.
- 7.
Brough, D.; Jouhara, H. The Aluminium Industry: A Review on State-of-the-Art Technologies, Environmental Impacts and Possibilities for Waste Heat Recovery. Int. J. Thermofluids 2020, 1–2, 100007. https://doi.org/10.1016/j.ijft.2019.100007.
- 8.
U.S. Department of Energy. Load Preheating Using Flue Gases from a Fuel-Fired Heating System. Process Heating Tip Sheet No. 9, Industrial Technologies Program. 2006. Available online: https://www.energy.gov/sites/prod/files/2014/05/f16/load_preheating.pdf (accessed on 5 February 2026).
- 9.
Migchielsen, J.M.; de Groot, J.D. Design Considerations for Charge Preheating Ovens. In Proceedings of the Light Metals 2006, San Antonio, TX, USA, 12–16 March 2006; p. 737.
- 10.
Jouhara, H.; Khordehgah, N.; Almahmoud, S.; et al. Waste Heat Recovery Technologies and Applications. Therm. Sci. Eng. Prog. 2018, 6, 268–289. https://doi.org/10.1016/j.tsep.2018.04.017.
- 11.
Venturelli, M.; Brough, D.; Milani, M.; et al. Comprehensive Numerical Model for the Analysis of Potential Heat Recovery Solutions in a Ceramic Industry. Int. J. Thermofluids 2021, 10, 100080. https://doi.org/10.1016/j.ijft.2021.100080.
- 12.
Jouhara, H.; Bertrand, D.; Axcell, B.; et al. Investigation on a Full-Scale Heat Pipe Heat Exchanger in the Ceramics Industry for Waste Heat Recovery. Energy 2021, 223, 120037. https://doi.org/10.1016/j.energy.2021.120037.
- 13.
Arink, T.; Hassan, M.I. Metal Scrap Preheating Using Flue Gas Waste Heat. Energy Procedia 2017, 105, 4788–4795. https://doi.org/10.1016/j.egypro.2017.03.945.
- 14.
Selvaraj, J.; Varun, V.S.; Vignesh; et al. Waste Heat Recovery from Metal Casting and Scrap Preheating Using Recovered Heat. Procedia Eng. 2014, 97, 267–276. https://doi.org/10.1016/j.proeng.2014.12.250.
- 15.
Kangvanskol, K.; Tangthieng, C. An Energy Analysis of a Slab Preheating Chamber for a Reheating Furnace. Eng. J. 2014, 18, 1–12. https://doi.org/10.4186/ej.2014.18.2.1.
This work is licensed under a Creative Commons Attribution 4.0 International License.
