2609005313
  • Open Access
  • Review

Highly Stable and Practical Sodium-Ion Batteries: Key Materials, Electrode Engineering, Manufacturing, and Prospects

  • Lu Yue 1,*,   
  • Yujie Zhang 1,   
  • Jiajun Wan 1,   
  • Guoxu Nie 1,   
  • Huajun Zhao 1,   
  • Wenhui Zhang 1,* and 
  • Huaiyu Shao 2,*

Received: 30 June 2026 | Revised: 10 September 2026 | Accepted: 29 September 2026 | Published: 16 November 2026

Abstract

Sodium-ion batteries (SIBs) are promising for large-scale energy storage owing to abundant sodium resources, low cost, and good manufacturing compatibility. However, their practical application remains limited by the structural stability of key materials, interfacial side reactions, cycle life, and safety. This review focuses on highly stable and practical SIBs and systematically summarizes the main failure mechanisms and stabilization strategies of cathode materials, anode materials, and electrolyte/electrode interfaces. Particular attention is paid to phase-transition suppression in layered oxides, framework strengthening of polyanionic compounds, defect regulation in Prussian blue/white materials, closed-pore structure optimization of hard carbon, solid electrolyte interphase (SEI)/cathode electrolyte interphase (CEI) formation, and interfacial stability of solid-state electrolytes. In addition, engineering strategies such as thick-electrode design, dry electrode manufacturing, thermal management, adaptive binders, and digital twin technologies are discussed from the perspective of material–electrode–device integration. Distinct from reviews centered on individual material classes, this work connects key-material failure mechanisms with electrode architecture, manufacturing, safety management, and industrialization, providing a full-chain materials–electrode–device–manufacturing perspective. Future efforts should focus on interfacial controllability, manufacturing consistency, and recycling sustainability to accelerate the large-scale application of SIBs.

References 

  • 1.

    International Renewable Energy Agency (IRENA). Renewable Capacity Statistics 2024; IRENA: Abu Dhabi, United Arab Emirates, 2024.

  • 2.

    National Energy Administration of China. Monitoring and Evaluation Report on Renewable Energy Power Development in China in 2023 (in Chinese); NEA: Beijing, China, 2024.

  • 3.

    International Energy Agency (IEA). Global EV Outlook 2024; IEA: Paris, France, 2024.

  • 4.

    Zhao, Y.; Kang, Y.; Wozny, J.; et al. Recycling of sodium-ion batteries. Nat. Rev. Mater. 2023, 8, 623–634. https://doi.org/10.1038/s41578-023-00574-w.

  • 5.

    Rystad Energy. Energy Storage Outlook 2025; Rystad Energy: Oslo, Norway, 2025.

  • 6.

    Zuo, W.; Innocenti, A.; Zarrabeitia, M.; et al. Layered Oxide Cathodes for Sodium-Ion Batteries: Storage Mechanism, Electrochemistry, and Techno-economics. Acc. Chem. Res. 2023, 56, 284–296. https://doi.org/10.1021/acs.accounts.2c00690.

  • 7.

    Wu, C.; Yang, Y.; Zhang, Y.; et al. Hard carbon for sodium-ion batteries: Progress, strategies and future perspective. Chem. Sci. 2024, 15, 6244–6268. https://doi.org/10.1039/d4sc00734d.

  • 8.

    Abdul Salam, A.F.; Zheng, X.; Chen, Z.; et al. Sodium-ion battery development since 2020 with future perspectives. J. Mater. Chem. A 2026, 14, 9115–9137. https://doi.org/10.1039/d5ta07726e.

  • 9.

    Sada, K.; Darga, J.; Manthiram, A. Challenges and Prospects of Sodium-Ion and Potassium-Ion Batteries for Mass Production. Adv. Energy Mater. 2023, 13, 2302321. https://doi.org/10.1002/aenm.202302321.

  • 10.

    Xiao, B.; Zheng, Y.; Song, M.; et al. Protonation Stimulates the Layered to Rock Salt Phase Transition of Ni-Rich Sodium Cathodes. Adv. Mater. 2024, 36, 2308380. https://doi.org/10.1002/adma.202308380.

  • 11.

    Bo, S.H.; Li, X.; Toumar, A.J.; et al. Layered-to-Rock-Salt Transformation in Desodiated NaxCrO2 (x ≤ 0.4). Chem. Mater. 2016, 28, 1419–1429. https://doi.org/10.1021/acs.chemmater.5b04626.

  • 12.

    Hu, J.; Li, X.; Liang, Q.; et al. Optimization Strategies of Na3V2(PO4)3 Cathode Materials for Sodium-Ion Batteries. Nano-Micro Lett. 2025, 17, 33. https://doi.org/10.1007/s40820-024-01526-x.

  • 13.

    Xiao, Y.; Xiao, J.; Zhao, H.; et al. Prussian Blue Analogues for Sodium-Ion Battery Cathodes: A Review of Mechanistic Insights, Current Challenges, and Future Pathways. Small 2024, 20, 2401957. https://doi.org/10.1002/smll.202401957.

  • 14.

    Meng, J.; Jia, G.; Yang, H.; et al. Recent advances for SEI of hard carbon anode in sodium-ion batteries: A mini review. Front. Chem. 2022, 10, 986541. https://doi.org/10.3389/fchem.2022.986541.

  • 15.

    Lu, Z.; Yang, H.; Guo, Y.; et al. Consummating ion desolvation in hard carbon anodes for reversible sodium storage. Nat. Commun. 2024, 15, 3497. https://doi.org/10.1038/s41467-024-47522-y.

  • 16.

    Zeng, Y.; Zhong, H.; Luo, Y.; et al. Interfacial engineering principles for hard carbon anodes in sodium-ion batteries: From mechanisms to synergistic strategies. Energy Environ. Sci. 2026, 19, 1775–1836. https://doi.org/10.1039/d5ee06849e.

  • 17.

    Zuo, W.; Liu, Z.; Dopilka, A.; et al. Next-generation anodes for high-energy and low-cost sodium-ion batteries. Nat. Rev. Mater. 2026, 11, 117–135. https://doi.org/10.1038/s41578-025-00857-4.

  • 18.

    He, Y.; Liu, D.; Li, Q.; et al. Advances in oxygen-containing functional groups-modified hard carbon anodes for sodium-ion batteries. Mater. Sci. Eng. R Rep. 2026, 168, 101143. https://doi.org/10.1016/j.mser.2025.101143.

  • 19.

    Massaro, A.; Lingua, G.; Bozza, F.; et al. P2-Type Na0.84Li0.1Ni0.27Mn0.63O2-Layered Oxide Na-Ion Battery Cathode: Structural Insights and Electrochemical Compatibility with Room-Temperature Ionic Liquids. Chem. Mater. 2024, 36, 7046–7055. https://doi.org/10.1021/acs.chemmater.4c01311.

  • 20.

    Domalanta, M.R.B.; Castro, M.T.; del Rosario, J.A.D.; et al. Cost Analysis of a Sodium-ion Battery Pack for Energy and Power Applications using Combined Multi-physics and Techno-Economic Modeling. Chem. Eng. Trans. 2022, 94, 139–144. https://doi.org/10.3303/cet2294023.

  • 21.

    Lodico, J.J.; Mecklenburg, M.; Chan, H.L.; et al. Operando spectral imaging of the lithium ion battery’s solid-electrolyte interphase. Sci. Adv. 2023, 9, eadg5135. https://doi.org/10.1126/sciadv.adg5135.

  • 22.

    Chen, Y.; Wu, W.; Gonzalez-Munoz, S.; et al. Nanoarchitecture factors of solid electrolyte interphase formation via 3D nano-rheology microscopy and surface force-distance spectroscopy. Nat. Commun. 2023, 14, 1321. https://doi.org/10.1038/s41467-023-37033-7.

  • 23.

    Steinberg, Y.; Sebti, E.; Moroz, I.B.; et al. Composition and Structure of the solid electrolyte interphase on Na-Ion Anodes Revealed by Exo- and Endogenous Dynamic Nuclear Polarization–NMR Spectroscopy. J. Am. Chem. Soc. 2024, 146, 24476–24492. https://doi.org/10.1021/jacs.4c06823.

  • 24.

    Marri, G.K.; Ee, Y.J.; He, Z.; et al. Recent advancements in internal and external thermoregulation strategies for lithium-ion batteries. Renew. Sustain. Energy Rev. 2026, 225, 116127. https://doi.org/10.1016/j.rser.2025.116127.

  • 25.

    Wang, X.; Wang, X.; Li, L.; et al. Coupled pore-forming and sodium supplementation strategies for asphalt-based hard carbon anodes to enhance the cycling stability of sodium-ion batteries. Mater. Sci. Eng. B 2026, 323, 118833. https://doi.org/10.1016/j.mseb.2025.118833.

  • 26.

    Walker, A.; Desai, J. Battery Energy Storage System Evaluation Method; U.S. Department of Energy Federal Energy Management Program (FEMP): Washington, DC, USA, 2023.

  • 27.

    Luo, T.; Lin, S.; Zhang, C.; et al. A facile synthetic strategy to MnS/NC submicrospheres for high-performance sodium-ion battery anodes. Mater. Res. Bull. 2026, 195, 113862. https://doi.org/10.1016/j.materresbull.2025.113862.

  • 28.

    Conover, D.R.; Crawford, A.J.; Fuller, J.; et al. Protocol for Uniformly Measuring and Expressing the Performance of Energy Storage Systems; Pacific Northwest National Laboratory and Sandia National Laboratories: Richland, WA, USA, 2016. https://doi.org/10.2172/1561194.

  • 29.

    IEC. ESRI and Standards Participation–New Proposal Initiated for Sodium-Ion Battery Chemistry; IEC: Geneva, Switzerland, 2024.

  • 30.

    Klick, S.; Laufen, H.; Schütte, M.; et al. Failure Mode and Degradation Analysis of a Commercial Sodium-Ion Battery with Severe Gassing Issue. Batter. Supercaps 2025, 8, e202400546. https://doi.org/10.1002/batt.202400546.

  • 31.

    Tan, R.; Hong, W.; Tang, J.; et al. BatteryLife: A Comprehensive Dataset and Benchmark for Battery Life Prediction. In Proceedings of the KDD ’25: The 31st ACM SIGKDD Conference on Knowledge Discovery and Data Mining, Toronto, ON, Canada, 3–7 August 2025; pp. 5789–5800. https://doi.org/10.1145/3711896.3737372.

  • 32.

    TWAICE. Simulation Model for Sodium-Ion Batteries—Aging Model for Emerging Sodium-Ion Technology; TWAICE Technologies GmbH: Munich, Germany, 2024.

  • 33.

    Feng, X.; Li, Y.; Li, Y.; et al. Unlocking the local structure of hard carbon to grasp sodium-ion diffusion behavior for advanced sodium-ion batteries. Energy Environ. Sci. 2024, 17, 1387–1396. https://doi.org/10.1039/d3ee03347c.

  • 34.

    Chen, T.; Ouyang, B.; Fan, X.; et al. Oxide cathodes for sodium-ion batteries: Designs, challenges, and perspectives. Carbon Energy 2022, 4, 170–199. https://doi.org/10.1002/cey2.153.

  • 35.

    Guo, Y.J.; Jin, R.X.; Fan, M.; et al. Sodium layered oxide cathodes: Properties, practicality and prospects. Chem. Soc. Rev. 2024, 53, 7828–7874. https://doi.org/10.1039/d4cs00415a.

  • 36.

    Liu, R.; Huang, W.; Liu, J.; et al. Revealing the Nature of Binary-Phase on Structural Stability of Sodium Layered Oxide Cathodes. Adv. Mater. 2024, 36, 2401048. https://doi.org/10.1002/adma.202401048.

  • 37.

    Chen, C.; Ding, Z.; Han, Z.; et al. Unraveling Atomically Irreversible Cation Migration in Sodium Layered Oxide Cathodes. J. Phys. Chem. Lett. 2020, 11, 5464–5470. https://doi.org/10.1021/acs.jpclett.0c01285.

  • 38.

    Jian, Z.C.; Guo, J.X.; Liu, Y.F.; et al. Cation migration in layered oxide cathodes for sodium-ion batteries: Fundamental failure mechanisms and practical modulation strategies. Chem. Sci. 2024, 15, 19698–19728. https://doi.org/10.1039/d4sc05206d.

  • 39.

    Hou, D.; Gabriel, E.; Graff, K.; et al. Thermal dynamics of P2-Na0.67Ni0.33Mn0.67O2 cathode materials for sodium ion batteries studied by in situ analysis. J. Mater. Res. 2022, 37, 1156–1163. https://doi.org/10.1557/s43578-022-00519-z.

  • 40.

    Chen, D.; Zhang, H.; Yang, H.Y.; et al. Promoting Na-ion storage in P2-Na0.67Ni0.33Mn0.67O2 cathode via synergetic Ti and Zn Co-incorporation. Appl. Phys. Lett. 2024, 124, 083904. https://doi.org/10.1063/5.0188032.

  • 41.

    Sun, Y.; Zhou, P.; Liu, S.; et al. Manipulating Na occupation and constructing protective film of P2-Na0.67Ni0.33Mn0.67O2 as long-term cycle stability cathode for sodium-ion batteries. J. Energy Chem. 2024, 88, 603–611. https://doi.org/10.1016/j.jechem.2023.09.042.

  • 42.

    Wu, S.Y.; Wu, F.; Ye, X.; et al. Inhibiting the P2–O2 phase transition of P2-Na0.67Ni0.33Mn0.67O2 via high-valence tungsten doping for sodium-ion batteries. Rare Met. 2025, 44, 3806–3816. https://doi.org/10.1007/s12598-024-03217-3.

  • 43.

    Liang, X.; Song, X.; Sun, H.H.; et al. High-energy and long-life O3-type layered cathode material for sodium-ion batteries. Nat. Commun. 2025, 16, 3505. https://doi.org/10.1038/s41467-025-58637-1.

  • 44.

    Zhao, X.; Liu, Q.; He, W.; et al. Uniform Al2O3 coating for improved cycling stability of O3-type sodium-ion batteries cathode: Mechanisms and performance insights. J. Energy Storage 2025, 131, 117548. https://doi.org/10.1016/j.est.2025.117548.

  • 45.

    Xiao, J.; Xiao, Y.; Wang, S.; et al. Surface engineering of P2-type cathode material targeting long-cycling and high-rate sodium-ion batteries. J. Energy Chem. 2024, 97, 444–452. https://doi.org/10.1016/j.jechem.2024.06.007.

  • 46.

    Wang, H.; Zhou, L.; Cheng, Z.; et al. Recent Advances on F-Doped Layered Transition Metal Oxides for Sodium Ion Batteries. Molecules 2023, 28, 8065. https://doi.org/10.3390/molecules28248065.

  • 47.

    Li, Y.; Zhou, Q.; Weng, S.; et al. Interfacial engineering to achieve an energy density of over 200 Wh kg−1 in sodium batteries. Nat. Energy 2022, 7, 511–519. https://doi.org/10.1038/s41560-022-01033-6.

  • 48.

    Massaro, A.; Porporato, S.; Botros, M.; et al. Entropy-driven mechanisms in P2-type layered oxide cathodes for sodium-ion batteries: New insights from first-principles and electrochemical analysis. J. Mater. Chem. A 2026, 14, 19341–19353. https://doi.org/10.1039/d6ta00673f.

  • 49.

    Huang, S.; Huang, M.; Liu, L.; et al. O3-NaNi1/3Fe1/3Mn1/3O2 material with excellent rate capability and cycling stability: A strategy of Ce4+ doping to facilitate reversible O3–P3–O3 phase transformation and mitigate lattice distortion. J. Alloys Compd. 2025, 1035, 181503. https://doi.org/10.1016/j.jallcom.2025.181503.

  • 50.

    Pamidi, V.; Trivedi, S.; Behara, S.; et al. Micron-sized single-crystal cathodes for sodium-ion batteries. iScience 2022, 25, 104205. https://doi.org/10.1016/j.isci.2022.104205.

  • 51.

    Xu, G.L.; Liu, X.; Zhou, X.; et al. Native lattice strain induced structural earthquake in sodium layered oxide cathodes. Nat. Commun. 2022, 13, 436. https://doi.org/10.1038/s41467-022-28052-x.

  • 52.

    Feng, L.; Xia, Y.; Guo, J.; et al. La-doped O3-type layered oxide cathode with enhanced cycle stability for sodium-ion batteries. Chem. Eng. J. 2024, 496, 154298. https://doi.org/10.1016/j.cej.2024.154298.

  • 53.

    Kuang, Y.; Wu, Y.; Zhang, H.; et al. Interface Issues of Layered Transition Metal Oxide Cathodes for Sodium-Ion Batteries: Current Status, Recent Advances, Strategies, and Prospects. Molecules 2024, 29, 5988. https://doi.org/10.3390/molecules29245988.

  • 54.

    Moossa, B.; Abraham, J.J.; Ahmed, A.M.; et al. Synergistic effect of NASICON Na3V2(PO4)2F3 and 2D MXene for high-performance symmetric Sodium-ion batteries. Mater. Res. Bull. 2025, 182, 113173. https://doi.org/10.1016/j.materresbull.2024.113173.

  • 55.

    Chen, J.; Wu, X.; Luo, Z.; et al. Nanotechnology engineering of polyanionic Na3V2(PO4)2F3 cathodes toward high-performance sodium-ion batteries. Chem. Sci. 2026, 17, 6848–6882. https://doi.org/10.1039/d5sc10141g.

  • 56.

    Liao, X.; Wu, X.; Xie, M.; et al. Leveraging high-entropy substitution to achieve V4+/V5+ redox couple and superior Na+ storage in Na3V2(PO4)3-based cathodes for sodium-ion battery. Energy Storage Mater. 2025, 77, 104166. https://doi.org/10.1016/j.ensm.2025.104166.

  • 57.

    Yin, R.; Guo, Z.; Liu, R.; et al. Ultrafast synthesis of Na3V2(PO4)3 cathode for high performance sodium-ion batteries. Chin. Chem. Lett. 2025, 36, 109643. https://doi.org/10.1016/j.cclet.2024.109643.

  • 58.

    Kang, Y.; Lin, X.; Tong, S.; et al. Synergetic impact of high-entropy microdoping modification in Na3V2(PO4)3. Chem. Commun. 2024, 60, 2512–2515. https://doi.org/10.1039/d4cc00033a.

  • 59.

    Zhou, M.; Zhou, X.; Li, L.; et al. Emerging high voltage V4+/V5+ redox reactions in Na3V2(PO4)3-based cathodes for sodium-ion batteries. Chem. Sci. 2024, 15, 8651–8663. https://doi.org/10.1039/d4sc01226g.

  • 60.

    Subaşı, Y.; Altenschmidt, L.; Lindgren, F.; et al. Synthesis and characterization of a crystalline Na4Fe3(PO4)2(P2O7) cathode material for sodium-ion batteries. J. Mater. Chem. A 2024, 12, 23506–23517. https://doi.org/10.1039/d4ta03554b.

  • 61.

    Xiong, F.; Li, J.; Zuo, C.; et al. Mg-Doped Na4Fe3(PO4)2(P2O7)/C Composite with Enhanced Intercalation Pseudocapacitance for Ultra-Stable and High-Rate Sodium-Ion Storage. Adv. Funct. Mater. 2023, 33, 2211257. https://doi.org/10.1002/adfm.202211257.

  • 62.

    Wu, H.; Chen, Y.; Wen, T.; et al. Advances in Vanadium-Redoxed Polyanions for High-Voltage Sodium-Ion Batteries. Batteries 2023, 9, 56. https://doi.org/10.3390/batteries9010056.

  • 63.

    Jiang, N.; Wang, X.; Zhou, H.; et al. Achieving Fast and Stable Sodium Storage in Na4Fe3(PO4)2(P2O7) via Entropy Engineering. Small 2024, 20, 2308681. https://doi.org/10.1002/smll.202308681.

  • 64.

    Zhou, Q.; Wang, Y.; Ou, R.; et al. Yolk-Shell Construction of Na3V2(PO4)2F3 with Copper Substitution Microsphere as High-Rate and Long-Cycling Cathode Materials for Sodium-Ion Batteries. Small 2024, 20, 2310699. https://doi.org/10.1002/smll.202310699.

  • 65.

    Mahato, S.; Das, S.; Gupta, D.; et al. Vanadium substituted Fe, Cr co-doped high performance C/Na3V2(PO4)2F3 cathode for sodium-ion batteries. J. Electroanal. Chem. 2024, 955, 118046. https://doi.org/10.1016/j.jelechem.2024.118046.

  • 66.

    Zhao, A.; Fang, Y.; Ai, X.; et al. Mixed polyanion cathode materials: Toward stable and high-energy sodium-ion batteries. J. Energy Chem. 2021, 60, 635–648. https://doi.org/10.1016/j.jechem.2021.01.014.

  • 67.

    Liang, Y.; Xu, L.; Chen, Z.; et al. Recent research progress in the application of Na3V2(PO4)2F3 cathode materials in sodium-ion batteries: Synthesis, modification, and battery optimization. Energy Mater. 2025, 5, 500115. https://doi.org/10.20517/energymater.2024.306.

  • 68.

    Zhou, B.; Gao, Y.; Lin, X.; et al. Bulk and interface engineering of Prussian blue analogue cathodes for high-performance sodium-ion batteries. Chem. Sci. 2025, 16, 13594–13628. https://doi.org/10.1039/d5sc02819a.

  • 69.

    Sun, S.; Jiang, X.; Wang, Z.; et al. Prussian blue analogues for high-performance sodium ion battery cathodes: Recent advances and challenges. Dalton Trans. 2025, 54, 14254–14261. https://doi.org/10.1039/d5dt01534k.

  • 70.

    Xu, X.; Zhu, S.; Yang, C.; et al. A novel strategy for the reduction of coordinated water in Prussian blue analogues for their application as cathode materials for sodium-ion batteries. J. Mater. Chem. A 2025, 13, 11848–11860. https://doi.org/10.1039/d5ta00120j.

  • 71.

    Li, Z.; Zhong, S.; Zhou, B.; et al. Synthesis of Low-Defect Iron-Based Prussian Blue with Low Water Content for High-Stability Sodium-Ion Batteries. Materials 2025, 18, 1455. https://doi.org/10.3390/ma18071455.

  • 72.

    Cheng, H.; Liu, Y.N.; Wang, D.; et al. Ball-milling synthesis of low-water and phase-stable Prussian blue for sodium-ion batteries. Solid State Ionics 2024, 414, 116633. https://doi.org/10.1016/j.ssi.2024.116633.

  • 73.

    Wang, Y.; Jiang, N.; Yang, C.; et al. High-entropy prussian blue analogs with 3D confinement effect for long-life sodium-ion batteries. J. Mater. Chem. A 2024, 12, 5170–5180. https://doi.org/10.1039/d3ta07671g.

  • 74.

    Li, C.; Xiao, Y.; Zhang, D.; et al. Stable Manganese-Based High-Entropy Prussian Blue for Enhanced Sodium-Ion Storage. Batteries 2025, 11, 328. https://doi.org/10.3390/batteries11090328.

  • 75.

    He, B.; Huang, M.; Yu, Y.; et al. High-Entropy Prussian Blue Analogs via a Solid-Solution Storage Mechanism for Long Cycle Sodium-Ion Batteries Cathodes. Chem. A Eur. J. 2025, 31, e202500880. https://doi.org/10.1002/chem.202500880.

  • 76.

    Liu, S.; Yu, H.; Zhao, Y.; et al. Inhibiting Phase Transitions of Prussian Blue Analogs with High-Entropy Strategy for Ultralong-Life Sodium-Ion Battery Cathodes. Small 2025, 21, 2504893. https://doi.org/10.1002/smll.202504893.

  • 77.

    Goel, G.; Sharma, M.; Tripathi, S.K.; et al. Prussian blue analogue as cathode materials in sodium ion batteries: A review. J. Energy Storage 2025, 126, 116995. https://doi.org/10.1016/j.est.2025.116995.

  • 78.

    Zhao, X.; Xing, Z.; Huang, C.; et al. Investigation of high-entropy Prussian blue analog as cathode material for aqueous sodium-ion batteries. J. Mater. Chem. A 2023, 11, 22835–22844. https://doi.org/10.1039/d3ta04349e.

  • 79.

    Shi, Q.; Qi, R.; Feng, X.; et al. Niobium-doped layered cathode material for high-power and low-temperature sodium-ion batteries. Nat. Commun. 2022, 13, 3205. https://doi.org/10.1038/s41467-022-30942-z.

  • 80.

    Yu, R.; Liu, S.; Li, X.; et al. Study on Thermal Behavior and Safety Properties of Na4Fe3(PO4)2(P2O7) and NaNi1/3Fe1/3Mn1/3O2 Cathode-Based Sodium Ion Battery. Batteries 2025, 11, 184. https://doi.org/10.3390/batteries11050184.

  • 81.

    Jing, Z.; Kong, L.; Mamoor, M.; et al. Rational Design of Prussian Blue Analogues for Ultralong and Wide-Temperature-Range Sodium-Ion Batteries. J. Am. Chem. Soc. 2025, 147, 3702–3713. https://doi.org/10.1021/jacs.4c16031.

  • 82.

    Wang, X.; Li, H.; Zhang, W.; et al. Unlocking fast and highly reversible sodium storage in Fe-based mixed polyanion cathodes for low-cost and high-performance sodium-ion batteries. J. Mater. Chem. A 2023, 11, 6978–6985. https://doi.org/10.1039/d3ta00014a.

  • 83.

    Zou, Z.; Mu, Y.; Han, M.; et al. Integrated polyanion-layered oxide cathodes enabling 100,000 cycle life for sodium-ion batteries. Energy Environ. Sci. 2025, 18, 2216–2230. https://doi.org/10.1039/d4ee05110f.

  • 84.

    Cai, T.; Chen, A.; Liang, S.; et al. Machine Learning for Design and Full Chain Research of High-Entropy Na-Ion Cathodes. Adv. Mater. 2025, 37, e08717. https://doi.org/10.1002/adma.202508717.

  • 85.

    Rexhausen, W.; Parsons, C.; Garg, U.; et al. Improved interfacial resistance and crystal-structure stability in a low-cobalt P2-type sodium-ion battery cathode material. arXiv 2024, arXiv:2408.01595.

  • 86.

    Pati, J.; Dhaka, R.S. Mixed polyanionic NaFe1.6V0.4(PO4)(SO4)2@CNT cathode for sodium-ion batteries: Electrochemical diffusion kinetics and distribution of relaxation time analysis at different temperatures. J. Power Sources 2024, 609, 234646. https://doi.org/10.1016/j.jpowsour.2024.234646.

  • 87.

    Yang, H.; Li, C.; He, L.; et al. Advances in modification strategies of Prussian blue-type cathode materials for sodium-ion batteries. J. Mater. Eng. 2025, 53, 42–56. https://doi.org/10.11868/j.issn.1001-4381.2024.000625.

  • 88.

    Zhang, L.; Zhang, Y.; Ma, Y.; et al. Research progress on sodium-ion battery cathode materials based on iron-based Prussian blue analogues. Energy Storage Sci. Technol. 2025, 14, 525–543. https://doi.org/10.19799/j.cnki.2095-4239.2024.0663.

  • 89.

    Chen, X.; Wang, C.; Zhao, Y.; et al. Recent progress in layered oxide cathodes for sodium-ion batteries: Stability, phase transition and solutions. J. Mater. Chem. A 2024, 12, 31797–31817. https://doi.org/10.1039/d4ta03372h.

  • 90.

    Rostami, H.; Valio, J.; Suominen, P.; et al. Advancements in cathode technology, recycling strategies, and market dynamics: A comprehensive review of sodium ion batteries. Chem. Eng. J. 2024, 495, 153471. https://doi.org/10.1016/j.cej.2024.153471.

  • 91.

    Wu, X.; Liu, A.; Lu, S.; et al. Enhancing Voltage Output in Polyanion-Type Cathode Materials for Sodium Ion Batteries. Batter. Supercaps 2024, 7, e202400290. https://doi.org/10.1002/batt.202400290.

  • 92.

    Li, Z. Optimization of Interface and Solid Phase Structure of Prussian Blue Analogue Cathode for Sodium Ion Battery. J. Adv. Phys. Chem. 2024, 13, 670–684. https://doi.org/10.12677/japc.2024.134069.

  • 93.

    Xu, C.; Zhao, J.; Yang, C.; et al. Polyanionic Cathode Materials for Practical Na-Ion Batteries toward High Energy Density and Long Cycle Life. ACS Cent. Sci. 2023, 9, 1721–1736. https://doi.org/10.1021/acscentsci.3c00907.

  • 94.

    Liu, Z.; Lu, Z.; Guo, S.; et al. Toward High Performance Anodes for Sodium-Ion Batteries: From Hard Carbons to Anode-Free Systems. ACS Cent. Sci. 2023, 9, 1076–1087. https://doi.org/10.1021/acscentsci.3c00301.

  • 95.

    Zhang, M.; Li, Y.; Wu, F.; et al. Boost sodium-ion batteries to commercialization: Strategies to enhance initial Coulombic efficiency of hard carbon anode. Nano Energy 2021, 82, 105738. https://doi.org/10.1016/j.nanoen.2020.105738.

  • 96.

    Tang, Z.; Zhang, R.; Wang, H.; et al. Revealing the closed pore formation of waste wood-derived hard carbon for advanced sodium-ion battery. Nat. Commun. 2023, 14, 6024. https://doi.org/10.1038/s41467-023-39637-5.

  • 97.

    Gabrijelcič, M.; Tratnik, B.; Kapun, G.; et al. Probing sodium structures and dynamics in hard carbon for Na-ion batteries using 23Na operando solid-state NMR spectroscopy. J. Mater. Chem. A 2025, 13, 1042–1056.

  • 98.

    Li, Q.; Liu, X.; Tao, Y.; et al. Sieving carbons promise practical anodes with extensible low-potential plateaus for sodium batteries. Natl. Sci. Rev. 2022, 9, nwac084. https://doi.org/10.1093/nsr/nwac084.

  • 99.

    Stratford, J.M.; Kleppe, A.K.; Keeble, D.S.; et al. Correlating Local Structure and Sodium Storage in Hard Carbon Anodes: Insights from Pair Distribution Function Analysis and Solid-State NMR. J. Am. Chem. Soc. 2021, 143, 14274–14286. https://doi.org/10.1021/jacs.1c06058.

  • 100.

    Reynolds, E.M.; Fitzpatrick, J.; Jones, M.O.; et al. Investigation of sodium insertion in hard carbon with operando small angle neutron scattering. J. Mater. Chem. A 2024, 12, 18469–18475. https://doi.org/10.1039/d3ta04739c.

  • 101.

    Qiu, C.; Li, A.; Qiu, D.; et al. One-Step Construction of Closed Pores Enabling High Plateau Capacity Hard Carbon Anodes for Sodium-Ion Batteries: Closed-Pore Formation and Energy Storage Mechanisms. ACS Nano 2024, 18, 11941–11954. https://doi.org/10.1021/acsnano.4c02046.

  • 102.

    Zhang, X.; Cao, Y.; Li, G.; et al. Exploring Carbonization Temperature to Create Closed Pores for Hard Carbon as High-Performance Sodium-Ion Battery Anodes. Small 2024, 20, 2311197. https://doi.org/10.1002/smll.202311197.

  • 103.

    Li, X.; Ding, C.; Liang, Q.; et al. Progress in hard carbons for sodium-ion batteries: Microstructure, sodium storage mechanism and initial Coulombic efficiency. J. Energy Storage 2024, 98, 112986. https://doi.org/10.1016/j.est.2024.112986.

  • 104.

    Ma, R.; Chen, Y.; Li, Q.; et al. Oxygen-driven closing pore formation in coal-based hard carbon for low-voltage rapid sodium storage. Chem. Eng. J. 2024, 493, 152389. https://doi.org/10.1016/j.cej.2024.152389.

  • 105.

    Wu, S.; Peng, H.; Xu, J.; et al. Nitrogen/phosphorus co-doped ultramicropores hard carbon spheres for rapid sodium storage. Carbon 2024, 218, 118756. https://doi.org/10.1016/j.carbon.2023.118756.

  • 106.

    Zhang, Y.; Zhang, S.W.; Chu, Y.; et al. Redefining closed pores in carbons by solvation structures for enhanced sodium storage. Nat. Commun. 2025, 16, 3634. https://doi.org/10.1038/s41467-025-59022-8.

  • 107.

    Qiu, R.; Ma, D.; Zheng, H.; et al. Performance degradation mechanisms and mitigation strategies of hard carbon anode and solid electrolyte interface for sodium-ion battery. Nano Energy 2024, 128, 109920. https://doi.org/10.1016/j.nanoen.2024.109920.

  • 108.

    Wang, L.; Jia, G.; Chen, Y.; et al. Review, analysis, and outlook of anode materials for sodium-ion batteries. Ionics 2026, 32, 1263–1307. https://doi.org/10.1007/s11581-025-06748-6.

  • 109.

    Gan, S.; Huang, Y.; Hong, N.; et al. Comprehensive Understanding of Closed Pores in Hard Carbon Anode for High-Energy Sodium-Ion Batteries. Nano-Micro Lett. 2025, 17, 325. https://doi.org/10.1007/s40820-025-01833-x.

  • 110.

    Li, R.; Yuan, B.; Feng, Y.; et al. Molecular-level precursor engineering enables high utilization of closed nanopores in hard carbon for sodium-ion batteries. Chem. Sci. 2026, 17, 10489–10503. https://doi.org/10.1039/d6sc01648k.

  • 111.

    Shen, T.; Sun, Y.; He, Z.; et al. Effect of pore structure regulation in coconut shell-derived hard carbon on sodium storage capacity. Electrochim. Acta 2025, 538, 147046. https://doi.org/10.1016/j.electacta.2025.147046.

  • 112.

    Shang, L.; Yuan, R.; Liu, H.; et al. Precursor screening of fruit shell derived hard carbons for low-potential sodium storage: A low lignin content supports the formation of closed pores. Carbon 2024, 223, 119038. https://doi.org/10.1016/j.carbon.2024.119038.

  • 113.

    Hou, W.; Ma, L.; Liu, Z.; et al. Construction of hard carbon with abundant closed ultra-micropores via a pre-oxidation strategy for high-efficiency sodium storage in the low potential plateau. J. Energy Chem. 2025, 105, 65–75. https://doi.org/10.1016/j.jechem.2025.01.042.

  • 114.

    Eren, E.O.; Senokos, E.; Scoppola, E.; et al. An enhanced three-stage model for sodium storage in hard carbons. Energy Environ. Sci. 2025, 18, 7859–7868. https://doi.org/10.1039/d4ee06029f.

  • 115.

    Jia, Z.; Hou, S.; Chen, X.; et al. Tailoring hard carbon interfaces in carbonate-based electrolytes for sodium-ion hybrid capacitors. Energy Mater. 2025, 5, 500073. https://doi.org/10.20517/energymater.2024.291.

  • 116.

    Lin, S.; Zhang, H.; Shu, C.; et al. Research Progress and Perspectives on Pre-Sodiation Strategies for Sodium-Ion Batteries. Adv. Funct. Mater. 2024, 34, 2409628. https://doi.org/10.1002/adfm.202409628.

  • 117.

    Liu, L.; Xiao, L.; Sun, Z.; et al. Rational manipulation of electrolyte to induce homogeneous SEI on hard carbon anode for sodium-ion battery. J. Energy Chem. 2024, 94, 414–429. https://doi.org/10.1016/j.jechem.2024.02.055.

  • 118.

    Liao, Y.; Liu, H.; Zhang, Y.; et al. A Weak-Fluorine-Bond Molecule Stabilizes Hard Carbon Anodes for Practical Sodium-Ion Batteries. ACS Nano 2025, 19, 30466–30475. https://doi.org/10.1021/acsnano.5c10983.

  • 119.

    Sun, Y.; Zuo, D.; Xu, C.; et al. A “grafting technique” to tailor the interfacial behavior of hard carbon anodes for stable sodium-ion batteries. Energy Environ. Sci. 2025, 18, 1911–1919. https://doi.org/10.1039/d4ee05305b.

  • 120.

    Zhang, W.; Du, Y.; Qiu, Y.; et al. Closed-Pore Engineering in Hard Carbon for Sodium Ion Storage: Advances, Challenges and Future Horizons. Adv. Energy Mater. 2025, 15, e03884. https://doi.org/10.1002/aenm.202503884.

  • 121.

    Sun, C.; Zhang, X.; Li, C.; et al. A safe, low-cost and high-efficiency presodiation strategy for pouch-type sodium-ion capacitors with high energy density. J. Energy Chem. 2022, 64, 442–450. https://doi.org/10.1016/j.jechem.2021.05.010.

  • 122.

    Wang, Y.; Yu, Z.; Li, Q.; et al. Recent advances in presodiation strategies for hard carbon anodes in sodium-ion batteries. Chem. Commun. 2025, 61, 15061–15067. https://doi.org/10.1039/d5cc04339e.

  • 123.

    Yuan, W.; Li, X.; Lu, X.; et al. Pre-sodiation strategies for sodium-ion batteries with hard carbon anodes: Techniques, challenges, and future directions. Mater. Sci. Eng. B 2025, 319, 118378. https://doi.org/10.1016/j.mseb.2025.118378.

  • 124.

    Deori, D.; Buragohain, M.; Son, Y.; et al. Self-Healing, Ga-Sb Alloy Confined Sn Anode for Stable Na-Ion Storage in Glyme Based Electrolytes. Small 2025, 21, 2504185. https://doi.org/10.1002/smll.202504185.

  • 125.

    Bai, X.; Wu, N.; Yu, G.; et al. Recent Advances in Anode Materials for Sodium-Ion Batteries. Inorganics 2023, 11, 289. https://doi.org/10.3390/inorganics11070289.

  • 126.

    Kojima, T.; Kitta, M.; Kataoka, R.; et al. Sodiation and Delithiation of Li4Ti5O12 for the Synthesis of Spinel-Type Sodium Titanium Oxide as an Anode Material for Sodium-Ion Batteries. J. Electrochem. Soc. 2023, 170, 090531. https://doi.org/10.1149/1945-7111/acf95d.

  • 127.

    Li, F.; Mo, F.; Zhong, C.; et al. A roadmap toward high-performance hard carbon for sodium-ion batteries: From fundamental studies on synthesis and mechanism to practical application. Energy Storage Mater. 2025, 83, 104668. https://doi.org/10.1016/j.ensm.2025.104668.

  • 128.

    Cheng, F.; Hu, J.; Zhang, W.; et al. Reviving ether-based electrolytes for sodium-ion batteries. Energy Environ. Sci. 2025, 18, 6874–6898. https://doi.org/10.1039/d5ee00725a.

  • 129.

    Chen, Z.; Yang, L.; Yu, G.; et al. Progress and Prospects in Sodium-Ion Battery Anode Materials: From Fundamentals to Material Engineering Strategies. Energy Storage Mater. 2026, 84, 104745. https://doi.org/10.1016/j.ensm.2025.104745.

  • 130.

    Hu, C.; Guo, S.; Huang, F.; et al. Carbonate ester-based sodium metal battery with high-capacity retention at −50 °C enabled by weak solvents and electrodeposited anode. Angew. Chem. Int. Ed. 2024, 63, e202407075. https://

  • 131.

    Zhang, L.; Liu, Z.; Zhang, X.; et al. Synergistic effect of cathode and electrolyte additives on stabilizing the anodic interface for sodium-based dual-carbon batteries. J. Alloys Compd. 2023, 942, 168863. https://doi.org/10.1016/j.jallcom.2023.168863.

  • 132.

    Liu, D.; Zhu, H.; Sun, R.; et al. Synergistic dual-additive boost cyclability of sodium-ion batteries. Energy Storage Sci. Technol. 2025, 14, 1858–1865. https://doi.org/10.19799/j.cnki.2095-4239.2024.1143.

  • 133.

    Dey, A.; Pramanik, A.; Purohit, S.; et al. Stable Na+ Ion Storage via Dual Active Sites Utilization in Covalent Organic Framework-Carbon Nanotube Composite. ChemSusChem 2025, 18, e202402325. https://doi.org/10.1002/cssc.202402325.

  • 134.

    Zhang, Z.; Fan, Z.; Li, J.; et al. Research Progress on Electrolyte Additives for Sodium Ion Batteries. Sustain. Polym. Energy 2024, 2, 10003. https://doi.org/10.35534/spe.2024.10003.

  • 135.

    Xia, M.; Chen, H.; Zheng, Z.; et al. Sodium-Difluoro(oxalato)Borate-Based Electrolytes for Long-Term Cycle Life and Enhanced Low-Temperature Sodium-Ion Batteries. Adv. Energy Mater. 2025, 15, 2403306. https://doi.org/10.1002/aenm.202403306.

  • 136.

    Edelman, D.A.; Brandt, T.G.; Temeche, E.; et al. Sodium-based solid electrolytes and interfacial stability. Towards solid-state sodium batteries. Mater. Today Commun. 2022, 32, 104009. https://doi.org/10.1016/j.mtcomm.2022.104009.

  • 137.

    Tian, Z.; Zou, Y.; Liu, G.; et al. Electrolyte Solvation Structure Design for Sodium Ion Batteries. Adv. Sci. 2022, 9, 2201207. https://doi.org/10.1002/advs.202201207.

  • 138.

    He, J.; Bhargav, A.; Su, L.; et al. Tuning the solvation structure with salts for stable sodium-metal batteries. Nat. Energy 2024, 9, 446–456. https://doi.org/10.1038/s41560-024-01469-y.

  • 139.

    Cheng, Z.; Zhang, Z.; Qiu, F.; et al. Regulating Solvation Shell to Fortify Anion–Cation Coordination for Enhanced Sodium Metal Battery Stability. ACS Energy Lett. 2025, 10, 177–184. https://doi.org/10.1021/acsenergylett.4c02751.

  • 140.

    Ke, J.; Kim, Y.; Su, L. Localized High-Concentration Electrolytes for Sodium Batteries: Fundamentals, Challenges, and Applications. ACS Appl. Energy Mater. 2025, 8, 8850–8861. https://doi.org/10.1021/acsaem.5c01221.

  • 141.

    Zhu, B.; Gao, J.; Li, S.; et al. Anion competitive coordination for solvation structure regulation in high-voltage sodium-ion batteries. Chem. Eng. J. 2025, 519, 165626. https://doi.org/10.1016/j.cej.2025.165626.

  • 142.

    Ren, D.; Lu, L.; Hua, R.; et al. Challenges and opportunities of practical sulfide-based all-solid-state batteries. eTransportation 2023, 18, 100272. https://doi.org/10.1016/j.etran.2023.100272.

  • 143.

    Yang, S.; Tang, Y.; Yao, Y.; et al. Sulfide electrolytes for all-solid-state sodium batteries: Fundamentals and modification strategies. Mater. Horiz. 2025, 12, 1058–1083. https://doi.org/10.1039/d4mh01218f.

  • 144.

    Kan, R.; Xu, Y.; Chen, R.; et al. Thermal effects of solid-state batteries at different temperature: Recent advances and perspectives. Energy Storage Mater. 2024, 68, 103366. https://doi.org/10.1016/j.ensm.2024.103366.

  • 145.

    Königsreiter, J.; Gadermaier, B.; Wilkening, H.M.R.; et al. Unveiling Ultra-High Ionic Conductivity in W-Doped Na3SbS4: Grain Boundary Effects and Pure Bulk Transport. J. Am. Chem. Soc. 2025, 147, 20092–20097. https://doi.org/10.1021/jacs.5c05842.

  • 146.

    Tao, H.Q.; Yin, J.; Shen, Y.; et al. Achievement of high ionic conductivity and electrochemical stability by W/Sn-doped Na3SbS4 conductors designed for all-solid-state sodium-ion batteries. J. Mater. Chem. C 2024, 12, 19296–19306. https://doi.org/10.1039/d4tc03109a.

  • 147.

    Huang, L.; Huang, C. Inorganic Sodium Solid-State Electrolytes: Progress, Existing Issues, and Solutions Towards High-Performance All Solid-State Batteries. Electrochem. Energy Rev. 2026, 9, 6. https://doi.org/10.1007/s41918-026-00279-y.

  • 148.

    Sun, C.; Xie, L.; Wang, B.; et al. Improve the cycling performance of solid-state sodium batteries through the design of a cathode interface buffering layer. Appl. Surf. Sci. 2025, 680, 161265. https://doi.org/10.1016/j.apsusc.2024.161265.

  • 149.

    Jiang, Y.; Wang, R.; Xiong, P.; et al. A solid dual-salt plastic crystal electrolyte enabling rapid ion transfer and stable interphases for high-performance solid-state sodium ion batteries. Chem. Sci. 2026, 17, 4529–4537. https://doi.org/10.1039/d5sc09186a.

  • 150.

    Tian, K.; Wei, C.; Wang, Z.; et al. Stable sodium metal anode enabled by interfacial room-temperature liquid metal engineering for high-performance sodium–sulfur batteries with carbonate-based electrolyte. Interdiscip. Mater. 2024, 3, 425–436. https://doi.org/10.1002/idm2.12163.

  • 151.

    Li, M.; Sun, C.; Zhang, R.; et al. Unveiling the Electrolyte and Solid Electrolyte Interphase in Sodium Ion Batteries: Mechanisms, Progress, and Perspectives. Adv. Mater. 2025, 37, e10882. https://doi.org/10.1002/adma.202510882.

  • 152.

    Li, W.; Wang, W.; Jing, S.; et al. Bio-inspired binder with multi-bond interactions for stress dissipation enables stabilization of electrode structure in lithium-ion batteries. Energy Storage Mater. 2026, 84, 104797. https://doi.org/10.1016/j.ensm.2025.104797.

  • 153.

    Jiang, H.; Mo, Z.; Xie, X.; et al. Bio-Inspired Self-Healing Silicon Anodes: Harnessing Tea Polyphenols to Enhance Lithium-Ion Battery Performance. ACS Appl. Mater. Interfaces 2024, 16, 59291–59301. https://doi.org/10.1021/acsami.4c12880.

  • 154.

    Passerini, S.; Barelli, L.; Baumann, M.; et al. Emerging Battery Technologies to Boost the Clean Energy Transition: Cost, Sustainability, and Performance Analysis; Springer: Cham, Switzerland, 2024. https://doi.org/10.1007/978-3-031-48359-2.

  • 155.

    Li, S.; Yang, Z.; Wang, S.B.; et al. Sulfide-based composite solid electrolyte films for all-solid-state batteries. Commun. Mater. 2024, 5, 44. https://doi.org/10.1038/s43246-024-00482-8.

  • 156.

    Cai, X.; Yue, Y.; Yi, Z.; et al. Challenges and industrial perspectives on the development of sodium ion batteries. Nano Energy 2024, 129, 110052. https://doi.org/10.1016/j.nanoen.2024.110052.

  • 157.

    Phogat, P.; Rawat, S.; Dey, S.; et al. Advancements and challenges in sodium-ion batteries: A comprehensive review of materials, mechanisms, and future directions for sustainable energy storage. J. Alloys Compd. 2025, 1020, 179544. https://doi.org/10.1016/j.jallcom.2025.179544.

  • 158.

    Liu, Q.S.; An, H.W.; Wang, X.F.; et al. Effective transport network driven by tortuosity gradient enables high-electrochem-active solid-state batteries. Natl. Sci. Rev. 2023, 10, nwac272. https://doi.org/10.1093/nsr/nwac272.

  • 159.

    Han, F.; Zhang, S.; Xia, J.; et al. Ultra-high rate and long cycle life sodium-based dual-ion batteries enabled by Li2TiO3-modified cathode-electrolyte-interphase. Energy Storage Mater. 2025, 74, 103912. https://doi.org/10.1016/j.ensm.2024.103912.

  • 160.

    Zhao, Q.; Butt, F.K.; Guo, Z.; et al. High-voltage P2-type manganese oxide cathode induced by titanium gradient modification for sodium ion batteries. Chem. Eng. J. 2021, 403, 126308. https://doi.org/10.1016/j.cej.2020.126308.

  • 161.

    Sun, S.; Rui, B.; Tan, X.; et al. Effects of electrolyte, state of charge, and strain rate on the mechanical properties of lithium-ion battery electrodes and separators. J. Mater. Chem. A 2025, 13, 20673–20687. https://doi.org/10.1039/d5ta02137e.

  • 162.

    Huang, Z.; Jiang, F.; Li, F.; et al. Towards high-performance cathodes: Concentration gradient structure design for lithium-ion batteries and sodium-ion batteries. Energy Storage Mater. 2026, 86, 105017. https://doi.org/10.1016/j.ensm.2026.105017.

  • 163.

    Zhou, H.; Gao, L.T.; Li, Y.; et al. Electrochemical performance of lithium-ion batteries with two-layer gradient electrode architectures. Electrochim. Acta 2024, 476, 143656. https://doi.org/10.1016/j.electacta.2023.143656.

  • 164.

    Wang, X.; Chen, Z.; Liu, S.; et al. Anode interphase design for fast-charging lithium-based rechargeable batteries. Energy Environ. Sci. 2025, 18, 2648–2667. https://doi.org/10.1039/d4ee06107a.

  • 165.

    Wang, Z.; Dai, C.; Chen, K.; et al. Perspectives on strategies and techniques for building robust thick electrodes for lithium-ion batteries. J. Power Sources 2022, 551, 232176. https://doi.org/10.1016/j.jpowsour.2022.232176.

  • 166.

    Shen, X.; Yu, H.; Ben, L.; et al. High energy density in ultra-thick and flexible electrodes enabled by designed conductive agent/binder composite. J. Energy Chem. 2024, 90, 133–143. https://doi.org/10.1016/j.jechem.2023.10.052.

  • 167.

    Ouyang, M.; Guo, Z.; Salinas-Farran, L.E.; et al. High-areal-capacity Na-ion battery electrode with high energy and power densities by simultaneous electrospinning-spraying fabrication. Energy Environ. Sci. 2025, 18, 6764–6779. https://doi.org/10.1039/d5ee01444a.

  • 168.

    Du, M.; Hao, Z.L.; Liu, Y.; et al. Architecture Engineering for Thick Electrodes in High-Energy Batteries: Challenges and Strategies. ACS Appl. Mater. Interfaces 2025, 17, 19230–19246. https://doi.org/10.1021/acsami.5c00264.

  • 169.

    Park, J.; Kim, J.; Kim, J.; et al. Sustainable and cost-effective electrode manufacturing for advanced lithium batteries: The roll-to-roll dry coating process. Chem. Sci. 2025, 16, 6598–6619. https://doi.org/10.1039/d5sc00059a.

  • 170.

    Bouguern, M.D.; Reddy, A.K.M.R.; Li, X.; et al. Engineering Dry Electrode Manufacturing for Sustainable Lithium-Ion Batteries. Batteries 2024, 10, 39. https://doi.org/10.3390/batteries10010039.

  • 171.

    Lee, K.H.; Shim, H.; Lee, S.H.; et al. Dual-fibrous PTFE structure enabling uniform and thick dry electrodes for high-energy-density and long-lasting batteries. Energy Environ. Sci. 2025, 18, 8446–8461. https://doi.org/10.1039/d5ee03240g.

  • 172.

    Hong, J.; Yoon, J.; Park, J.W.; et al. Optimization of PTFE fibrillation in dry electrode process for scalable all-solid-state battery manufacturing. J. Power Sources 2025, 655, 237925. https://doi.org/10.1016/j.jpowsour.2025.237925.

  • 173.

    Zhang, K.; Li, D.; Wang, X.; et al. Dry Electrode Processing Technology and Binders. Materials 2024, 17, 2349. https://doi.org/10.3390/ma17102349.

  • 174.

    Choi, J.; Polyzos, G.; Humphrey, H.E.; et al. Long carbon fibers boost performance of dry processed Li-ion battery electrodes. J. Power Sources 2025, 640, 236603. https://doi.org/10.1016/j.jpowsour.2025.236603.

  • 175.

    Asrafali, S.P.; Periyasamy, T.; Kim, S.C. Rapid Transformation in Wetting Properties of PTFE Membrane Using Plasma Treatment. Polymers 2023, 15, 3874. https://doi.org/10.3390/polym15193874.

  • 176.

    Kühn, J.; Schmidt, F.; Seete, P.; et al. Towards Scalable Production of Sodium-Ion Batteries: Solvent-Free Layered-Oxide Cathodes and Aqueous-Processed Hard Carbon Anodes for Cost-Effective Full-Cell Manufacturing. Batter. Supercaps 2025, 8, e202400572. https://doi.org/10.1002/batt.202400572.

  • 177.

    Kim, B.; Yoo, Y. Dry-Electrode Manufacturing for High-Energy Lithium-Ion Batteries: Principles, Advances, and Challenges. Elastomers Compos. 2025, 60, 39–50. https://doi.org/10.7473/EC.2025.60.1.39.

  • 178.

    Schumm, B.; Dupuy, A.; Lux, M.; et al. Dry Battery Electrode Technology: From Early Concepts to Industrial Applications. Adv. Energy Mater. 2025, 15, 2406011. https://doi.org/10.1002/aenm.202406011.

  • 179.

    Zhang, L.; Yu, J. Computer-aided thermal energy storage research of electric vehicle battery thermal management system. Therm. Sci. 2025, 29, 4157–4165. https://doi.org/10.2298/tsci2506157z.

  • 180.

    Zhan, S.; Liang, L.; Li, Z.; et al. Topology optimization of liquid cooling plate for lithium battery heat dissipation based on a bionic leaf-vein structure. Int. J. Heat Mass Transf. 2024, 231, 125898. https://doi.org/10.1016/j.ijheatmasstransfer.2024.125898.

  • 181.

    Zhan, S.; Shi, X.; Liu, Y.; et al. Topology optimization of a new leaf-vein type bionic channel liquid-cooling plate for lithium batteries. Int. J. Heat Fluid Flow. 2025, 116, 109932. https://doi.org/10.1016/j.ijheatfluidflow.2025.109932.

  • 182.

    Zhang, X.; Luo, S.; Wu, Y.; et al. Research progress of composite phase change materials for thermal management and thermal runaway protection of lithium-ion batteries. Energy Storage Sci. Technol. 2025, 14, 1040–1053. https://doi.org/10.19799/j.cnki.2095-4239.2025.0137.

  • 183.

    Yang, Z.L.; Walvekar, R.; Wong, W.P.; et al. Advances in phase change materials, heat transfer enhancement techniques, and their applications in thermal energy storage: A comprehensive review. J. Energy Storage 2024, 87, 111329. https://doi.org/10.1016/j.est.2024.111329.

  • 184.

    Liu, F.; Wang, J.; Wang, F.; et al. Battery thermal safety management with form-stable and flame-retardant phase change materials. Int. J. Heat Mass Transf. 2024, 218, 124764. https://doi.org/10.1016/j.ijheatmasstransfer.2023.124764.

  • 185.

    He, R.; Cai, C.; Li, S.; et al. Enhancing Electrode Performance through Triple Distribution Modulation of Active Material, Conductive Agent, and Porosity. Small 2024, 20, 2311044. https://doi.org/10.1002/smll.202311044.

  • 186.

    Kotronia, A.; van Ekeren, W.W.A.; Asfaw, H.D.; et al. Impact of Binders on Self-Discharge in Graphite Dual-Ion Batteries. Electrochem. Commun. 2023, 146, 107424. https://doi.org/10.1016/j.elecom.2022.107424.

  • 187.

    Lin, X.; Chen, A.; Yang, C.; et al. A Room-Temperature Self-Healing Liquid Metal-Infilled Microcapsule Driven by Coaxial Flow Focusing for High-Performance Lithium-Ion Battery Anode. Small 2024, 20, 2307071. https://doi.org/10.1002/smll.202307071.

  • 188.

    Long, X.; Xie, L.; Huang, C.; et al. Self-Healing Ion-Conductive Binder for High-Performance SiOx Anodes in Lithium-Ion Batteries. ACS Appl. Mater. Interfaces 2025, 17, 53402–53412. https://doi.org/10.1021/acsami.5c11054.

  • 189.

    Xian, J.; Jiao, J.; Yi, C.; et al. The synergistic optimization of the LA133 binder and electrode interface using sodium lignosulfonate comprehensively enhances the electrochemical performance of sodium-ion batteries. J. Energy Storage 2025, 135, 118403. https://doi.org/10.1016/j.est.2025.118403.

  • 190.

    Yao, Z.; Yin, R.; Peng, Q. A review on thermal management system and employed biomimetic technology to enhance lithium-ion battery packs for electric vehicles. J. Energy Storage 2025, 111, 115399. https://doi.org/10.1016/j.est.2025.115399.

  • 191.

    Shi, Y.; Gao, F.; Xie, Y.; et al. In Situ interlocked gradient adaptive network binder with robust adhesion and cycle performance for silicon anodes. J. Power Sources 2023, 580, 233267. https://doi.org/10.1016/j.jpowsour.2023.233267.

  • 192.

    Dubarry, M.; Howey, D.; Wu, B.; et al. Enabling battery digital twins at the industrial scale. Joule 2023, 7, 1134–1144. https://doi.org/10.1016/j.joule.2023.05.005.

  • 193.

    Zhao, Y.; Du, H.; Kang, Y.; et al. Spent battery regeneration for better recycling. Nat. Rev. Mater. 2025, 10, 722–724. https://doi.org/10.1038/s41578-025-00816-z.

  • 194.

    Yao, A.; Benson, S.M.; Chueh, W.C. Critically assessing sodium-ion technology roadmaps and scenarios for techno-economic competitiveness against lithium-ion batteries. Nat. Energy 2025, 10, 404–416. https://doi.org/10.1038/s41560-024-01701-9.

  • 195.

    Ruppert, J.; Voß, P.; Ihlbrock, L.; et al. Analyzing material and production costs for lithium-ion and sodium-ion batteries using process-based cost modeling—CellEst 3.0. J. Power Sources Adv. 2025, 36, 100190. https://doi.org/10.1016/j.powera.2025.100190.

  • 196.

    Mariyappan, S.; Desai, P.; Morcrette, M.; et al. From lab to market with sustainable sodium-ion batteries. Nat. Sustain. 2026, 9, 360–371. https://doi.org/10.1038/s41893-025-01701-x.

  • 197.

    Zhang, L.; Huang, S.; Ding, Y.; et al. Research progress in the preparation of sodium-ion battery anode materials using ball milling. RSC Adv. 2025, 15, 6324–6341. https://doi.org/10.1039/d4ra08061k.

  • 198.

    Marangon, V.; Bischof, K.; Regalado, A.A.; et al. Cell design and chemistry of commercial sodium-ion battery cells. J. Power Sources 2025, 634, 236496. https://doi.org/10.1016/j.jpowsour.2025.236496.

  • 199.

    Wang, Y.; Bian, M.; Chen, Y.; et al. Recycling waste cotton into C@SiOx/MoSe2@CS@CF composites: Design, synthesis and high-performance sodium-ion battery anode applications. Electrochim. Acta 2025, 543, 147545. https://doi.org/10.1016/j.electacta.2025.147545.

  • 200.

    Wu, Y.; Wang, B.; Luo, Z.; et al. High-Voltage Sodium-Ion Batteries: Challenges and Design Strategies. Adv. Funct. Mater. 2025, 35, 2506098. https://doi.org/10.1002/adfm.202506098.

  • 201.

    Dreyer, S.L.; Maddar, F.M.; Kondrakov, A.; et al. Elucidating Gas Evolution of Prussian White Cathodes for Sodium-ion Battery Application: The Effect of Electrolyte and Moisture. Batter. Supercaps 2024, 7, e202300595. https://doi.org/10.1002/batt.202300595.

  • 202.

    Muneer, W.; Khan, M.I.; Shah, S.K.; et al. Advances in prussian blue analogues: A comprehensive review on synthesis methods and battery applications. Mater. Chem. Phys. 2025, 332, 130248. https://doi.org/10.1016/j.matchemphys.2024.130248.

  • 203.

    Gharat, V.V.; Yadav, M.D. Recent progress of Prussian white analogues as cathode active material for sodium-ion battery. J. Alloys Compd. 2025, 1039, 183244. https://doi.org/10.1016/j.jallcom.2025.183244.

  • 204.

    Jia, S.; Zhang, B.; Gao, J.; et al. Biomass-derived hard carbon anodes: From structural engineering to industrial sodium-ion battery applications. Energy Storage Mater. 2025, 80, 104420. https://doi.org/10.1016/j.ensm.2025.104420.

  • 205.

    Huang, Z.; Zhong, L.; Huang, J.; et al. Closed pore engineering of hard carbons toward remarkable sodium-ion storage. J. Power Sources 2025, 654, 237847. https://doi.org/10.1016/j.jpowsour.2025.237847.

  • 206.

    Zhou, L.; Cui, Y.; Niu, P.; et al. Biomass-derived hard carbon material for high-capacity sodium-ion battery anode through structure regulation. Carbon 2025, 231, 119733. https://doi.org/10.1016/j.carbon.2024.119733.

  • 207.

    Qu, X.; Yu, X.; Liao, Y.; et al. Structural regulations of biomass-derived hard carbon for high-performance sodium-ion batteries. J. Power Sources 2025, 654, 237786. https://doi.org/10.1016/j.jpowsour.2025.237786.

  • 208.

    Lin, W.; Min, W.; Zhang, Q.; et al. Bimetallic co-doping strategy for layered oxides in high-performance sodium-ion batteries. J. Colloid Interface Sci. 2026, 702, 138985. https://doi.org/10.1016/j.jcis.2025.138985.

  • 209.

    Shakourian-Fard, M.; Ghenaatian, H.R.; Pasban, S.; et al. In silico navigation of Na+ ion solvation in deep eutectic solvents to propel the next wave of sodium-ion battery electrolytes. J. Mater. Chem. A 2025, 13, 33442–33456. https://doi.org/10.1039/d5ta03220b.

  • 210.

    Jiang, J.; Guo, C.; Ali, S.; et al. Understanding the stabilizing effect of K+ on the sodium manganese hexacyanoferrate for sodium-ion batteries. Nano Energy 2024, 129, 110007. https://doi.org/10.1016/j.nanoen.2024.110007.

  • 211.

    Wei, R.; Lu, Y.; Ren, W.; et al. Enhancing reversible Na-ion intercalation by introducing K-ions into layered vanadyl phosphate for sodium-ion battery cathodes. J. Phys. Energy 2024, 6, 025022. https://doi.org/10.1088/2515-7655/ad3c27.

  • 212.

    Zhu, Q.; Wang, J.; Wu, L.; et al. A >200 Wh kg−1 anode-free Na pouch battery at −40 °C enabled by manipulating electrolyte equilibrium. Natl. Sci. Rev. 2025, 12, nwaf124. https://doi.org/10.1093/nsr/nwaf124.

  • 213.

    Zhang, X.; Yang, S.; Deng, C.; et al. Selective recovery of metals in spent batteries by electrochemical precipitation to cathode material for sodium-ion batteries. Heliyon 2024, 10, e27127. https://doi.org/10.1016/j.heliyon.2024.e27127.

  • 214.

    Zhang, J.; Wang, Y.; Kang, Y.; et al. Cathode Recycling of Spent Sodium Ion Batteries. Energy Mater. Adv. 2024, 5, 0128. https://doi.org/10.34133/energymatadv.0128.

  • 215.

    Joo, J.; Moon, J.K.; Jang, Y. A study on the desalination process for high-concentration Na2SO4 using pilot-scale bipolar membrane electrodialysis. Desalin. Water Treat. 2025, 322, 101222. https://doi.org/10.1016/j.dwt.2025.101222.

  • 216.

    Ye, N.; Yan, T.; Jiang, Z.; et al. A review: Conventional and supercritical hydro/solvothermal synthesis of ultrafine particles as cathode in lithium battery. Ceram. Int. 2018, 44, 4521–4537. https://doi.org/10.1016/j.ceramint.2017.12.236.

  • 217.

    Liu, S.; Zhou, W.; Song, X.D.; et al. Hard carbons prepared by a salt-assisted hydrothermal method as anodes for the sodium-ion battery. New Carbon Mater. 2025, 40, 346–354. https://doi.org/10.1016/s1872-5805(25)60954-1.

  • 218.

    Zhang, C.; Wang, Y.; Sun, H. Dry-coating electrode fabrication for sustainable, high-performance batteries. Sci. China Chem. 2025, 68, 6391–6402. https://doi.org/10.1007/s11426-025-3119-x.

  • 219.

    Zhou, H.; Yu, Y.; Wang, K.; et al. A YOLOv8-Based Approach for Real-Time Lithium-Ion Battery Electrode Defect Detection with High Accuracy. Electronics 2024, 13, 173. https://doi.org/10.3390/electronics13010173.

  • 220.

    Nozarijouybari, Z.; Fathy, H.K. Machine learning for battery systems applications: Progress, challenges, and opportunities. J. Power Sources 2024, 601, 234272. https://doi.org/10.1016/j.jpowsour.2024.234272.

  • 221.

    Kim, S.; Lee, H.; Lim, J.; et al. Digital Twin Battery Modeling and Simulations: A New Analysis and Design Tool for Rechargeable Batteries. ACS Energy Lett. 2024, 9, 5225–5239. https://doi.org/10.1021/acsenergylett.4c01931.

  • 222.

    Kausthubharam; Vishnugopi, B.S.; Sengupta, A.; et al. Perspective on Thermal Stability and Safety of Sodium-Ion Batteries. ACS Energy Lett. 2025, 10, 5383–5397. https://doi.org/10.1021/acsenergylett.5c02345.

  • 223.

    National Development and Reform Commission; National Energy Administration. Implementation Plan for the Development of New Energy Storage during the 14th Five-Year Plan Period (in Chinese); NEA: Beijing, China, 2022.

  • 224.

    European Commission. Battery 2030+ Roadmap 2024–2030; Publications Office of the European Union: Luxembourg, 2024.

  • 225.

    U.S. Department of Energy. Bipartisan Infrastructure Law: Battery Material Processing and Manufacturing Grants; DOE: Washington, DC, USA, 2023.

  • 226.

    Gan, S.; Zeng, X.; Liu, D.; et al. Direct upcycling of spent layered oxide cathodes via a dual-functional eutectic salt for sodium-ion batteries. J. Mater. Chem. A 2025, 13, 24880–24888. https://doi.org/10.1039/d5ta02389k.

  • 227.

    Li, H.; Wu, F.; Wang, J.; et al. Anode-free sodium metal batteries: Optimisation of electrolytes and interphases. Energy Environ. Sci. 2025, 18, 3887–3916. https://doi.org/10.1039/d5ee00136f.

  • 228.

    Li, A.M.; Pollard, T.P.; Wang, Z.; et al. Non-fluorinated electrolyte for high-voltage anode-free sodium metal battery. Nat. Sustain. 2026, 9, 306–316. https://doi.org/10.1038/s41893-025-01710-w.

  • 229.

    Liu, L.; Cai, Z.; Yang, S.; et al. Multifunctional High-Entropy Alloy Nanolayer Toward Long-Life Anode-Free Sodium Metal Battery. Adv. Mater. 2025, 37, 2413331. https://doi.org/10.1002/adma.202413331.

  • 230.

    Shi, J.; Wang, D.; Liu, Q.; et al. Intermetallic Layers with Tuned Na Nucleation and Transport for Anode-Free Sodium Metal Batteries. Nano Lett. 2025, 25, 1800–1807. https://doi.org/10.1021/acs.nanolett.4c04282.

  • 231.

    Alzamer, H.; Jaafreh, R.; Kim, J.G.; et al. Artificial Intelligence and Li Ion Batteries: Basics and Breakthroughs in Electrolyte Materials Discovery. Crystals 2025, 15, 114. https://doi.org/10.3390/cryst15020114.

  • 232.

    Meng, K.; Bai, K.; Sun, S.; et al. Artificial intelligence driven design of cathode materials for sodium-ion batteries using graph deep learning method. J. Energy Storage 2024, 101, 113809. https://doi.org/10.1016/j.est.2024.113809.

  • 233.

    Cong, J.; Luo, S. Artificial intelligence empowering innovation in key materials for sodium-ion batteries: Machine learning driven design and optimization of cathode and anode materials. J. Energy Chem. 2026, 116, 434–453. https://doi.org/10.1016/j.jechem.2026.01.011.

Share this article:
How to Cite
Yue, L.; Zhang, Y.; Wan, J.; Nie, G.; Zhao, H.; Zhang, W.; Shao, H. Highly Stable and Practical Sodium-Ion Batteries: Key Materials, Electrode Engineering, Manufacturing, and Prospects. Sustainable Engineering Novit 2026, 2 (4), 1. https://doi.org/10.53941/sen.2026.100015.
RIS
BibTex
Copyright & License
article copyright Image
Copyright (c) 2026 by the authors.
Article Metrics
39
Article Views
0
Citations