Experimental Investigation of Convective Heat-Transfer Performance of Graphite and SiO2-Graphite Nanofluids for Automotive Radiator Applications

Luke O. Ajuka; Peter O. Akindele

doi:10.53941/tsa.2026.100023

Abstract

Efficient heat transfers in radiators are vital for the life of the engine, to avoid being overheated. Conventional fluids are inefficient in engine cooling, and alternate solutions to prolong engine life must capture enhanced heat transfer, including the application of nanofluids. Despite growing interest in nanofluid-based radiator cooling, limited studies have quantified the comparative performance of base fluids, Gr/Water-EG single nanofluid and SiO₂-Gr/Water-EG hybrid nanofluids under varying concentrations, individually. This study experimentally examined their thermophysical and convective heat-transfer behaviour in a radiator channel flow using thermal conductivity, viscosity, inlet temperature, Nusselt number and Reynolds number as performance indicators. Increasing nanoparticle volumetric fraction enhanced the thermal conductivity of both graphite and SiO₂-Gr nanofluids, whereas increasing ethylene glycol (EG) fraction in the Water-EG base fluid reduced thermal conductivity. Viscosity also increased with volumetric fraction for all fluids, confirming the concentration-induced trade-off between heat-transfer enhancement and flow resistance. The Nusselt number increased with inlet temperature for the Water-EG base fluid and graphite nanofluid, indicating improved convective heat-transfer response at elevated temperature. Conversely, the SiO₂-Gr composite nanofluid showed a reduction in Nusselt number with increasing inlet temperature, suggesting temperature-sensitive transport behaviour; however, at 51 °C, its Nusselt number remained approximately 26% higher than Gr/Water-EG. Reynolds number increased with inlet temperature for the base fluid and graphite nanofluid, indicating stronger inertial flow. Although the hybrid SiO₂-graphite nanofluid exhibited higher Reynolds numbers than the graphite nanofluid under the tested conditions, the observed reduction in Nusselt number with increasing inlet temperature suggests that the thermal enhancement mechanism may be influenced by alterations in fluid properties and particle interactions. Nevertheless, the SiO₂-Gr nanofluid maintained a Reynolds number 66.7% higher than Gr/Water-EG at 51 °C. Overall, the hybrid nanofluid improved heat-transfer performance, although viscosity and flow penalties require optimization for radiators in automotive application.

References

1.
Yaw, C.T.; Koh, S.P.; Sandhya, M.; et al. Heat Transfer Enhancement by Hybrid Nano Additives—Graphene Nanoplatelets/Cellulose Nanocrystal for the Automobile Cooling System (Radiator). Nanomaterials 2023, 13, 808. https://doi.org/10.3390/nano13050808.
2.
Harikrishnan, A.R.; Dhar, P.; Agnihotri, P.K.; et al. Effects of interplay of nanoparticles, surfactants and base fluid on the surface tension of nanocolloids. Eur. Phys. J. E 2017, 40, 1–31. https://doi.org/10.1140/epje/i2017-11541-5.
3.
Hafeez, M.B.; Amin, R.; Nisar, K.S.; et al. Heat transfer enhancement through nanofluids with applications in automobile radiator. Case Stud. Therm. Eng. 2021, 27, 101192. https://doi.org/10.1016/j.csite.2021.101192.
4.
Ardika, R.; Sudarno, S.; Winangun, K.; et al. The Effect of Using Variations of Radiator Fluid on the Effectiveness of Engine Cooling and the Rate of Corrosion of Radiator Materials in 1300 cc Cars. Eng. Proc. 2025, 84, 11. https://doi.org/10.3390/engproc2025084011.
5.
Atanatizante. Ethylene Glycol and Engine Cooling. F1technical.net, January 25, 2020. Available online: https://www.f1technical.net/forum/viewtopic.php?t=28740 (accessed on 10 June 2024).
6.
Tan, P.; Wang, P.; Fang, L.; et al. Exploring the performance of the thermal management system in a FCV based on real vehicle testing under different driving conditions. Energy 2025, 336, 138529. https://doi.org/10.1016/j.energy.2025.138529.
7.
Dhumal, A.; Ambhore, N.; Kore, S.; et al. Investigation of the Effect of Different Fins Configurations on the Thermal Performance of the Radiator. J. Adv. Res. Fluid Mech. Therm. Sci. 2024, 116, 27–39. https://doi.org/10.37934/arfmts.116.1.2739.
8.
Momin, M.; Atofarati, E.O.; Oladipo, S.; et al. Experimental characterization and predictive modelling of Al2O3/MWCNT hybrid nanofluid thermophysical properties using ANN, ANFIS, FCM and hybrid techniques. J. Therm. Anal. Calorim. 2026, 151, 11041–11071. https://doi.org/10.1007/s10973-026-15698-8.
9.
Petinrin, M.O.; Ajuka, L.O.; Adebayo, A.S.; et al. Experimental Study of Flow and Heat Transfer in Rectangular Ducts with Ribbed Surfaces. In Proceedings of the International Conference on Innovative Academic Studies, Konya, Turkey, 10–13 September 2022.
10.
Hussein, A.M.; Dawood, H.K.; Bakara, R.A.; et al. Numerical study on turbulent forced convective heat transfer using nanofluids TiO₂ in an automotive cooling system. Case Stud. Therm. Eng. 2017, 9, 72–78. https://doi.org/10.1016/j.csite.2016.11.005.
11.
Ajuka, L.O.; Enweremadu, C.C. Comparative performance of liquid cooled micro/mini channel heat exchangers and macro-scale shell and tube exchangers in phase turbulent flow: A systematic review. J. Therm. Anal. Calorim. 2026, 1–26. https://doi.org/10.1007/s10973-026-15538-9.
12.
Oshionebo, F.D.; Kavaz, D.; Ozsahin, D.U.; et al. Optimized Nanofluid Fluids Enhance Thermal Performance in Ruffled Fin Automotive Radiators. Sci. Rep. 2025, 15, 43756. https://doi.org/10.1038/s41598-025-26764-w.
13.
Yu, W.; Xie, H. A Review on Nanofluids: Preparation, Stability Mechanisms, and Applications. J. Nanomater. 2012, 2012, 435873. https://doi.org/10.1155/2012/435873.
14.
Alami, A.H.; Ramadan, M.; Tawalbeh, M.; et al. A critical insight on nanofluids for heat transfer enhancement. Sci. Rep. 2023, 13, 15303. https://doi.org/10.1038/s41598-023-42489-0.
15.
Wakif, A.; Chamkha, A.; Thumma, T.; et al. Thermal radiation and surface roughness effects on the thermo-magneto-hydrodynamic stability of alumina–copper oxide hybrid nanofluids utilizing the generalized Buongiorno’s nanofluid model. J. Therm. Anal. Calorim. 2021, 143, 1201–1220. https://doi.org/10.1007/s10973-020-09488-z.
16.
Chiam, H.W.; Azmi, W.H.; Usri, N.A.; et al. Thermal conductivity and viscosity of Al₂O₃ nanofluids for different based ratio of water and ethylene glycol mixture. Exp. Therm. Fluid Sci. 2017, 81, 420–429. https://doi.org/10.1016/j.expthermflusci.2016.09.013.
17.
Levin, M.L.; Miller, M.A. Maxwell’s Treatise on Electricity and Magnetism. Sov. Phys. Uspekhi 1981, 24, 904–913.
18.
Rasool, G.; Wakif, A. Numerical spectral examination of EMHD mixed convective flow of second-grade nanofluid towards a vertical Riga plate using an advanced version of the revised Buongiorno’s nanofluid model. J. Therm. Anal. Calorim. 2021, 143, 2379–2393. https://doi.org/10.1007/s10973-020-09865-8.
19.
Soltani, F.; Toghraie, D.; Karimipour, A. Experimental measurements of thermal conductivity of engine oil-based hybrid and mono nanofluids with tungsten oxide (WO₃) and MWCNTs inclusions. Powder Technol. 2020, 371, 37–44. https://doi.org/10.1016/j.powtec.2020.05.059.
20.
Esapour, M.; Hamzehnezhad, A.; Rabienataj Darzi, A.A.; et al. Melting and solidification of PCM embedded in porous metal foam in horizontal multi-tube heat storage system. Energy Convers. Manag. 2018, 171, 398–410. https://doi.org/10.1016/j.enconman.2018.05.086.
21.
Jamshed, W.; Nisar, K.S.; Ibrahim, R.W.; et al. Computational frame work of Cattaneo-Christov heat flux effects on Engine Oil based Williamson hybrid nanofluids: A thermal case study. Case Stud. Therm. Eng. 2021, 26, 101179. https://doi.org/10.1016/j.csite.2021.101179.
22.
Sathish, T.; Giri, J.; Saravanan, R.; et al. Amplifying thermal performance of solar flat plate collector by Al₂O₃/Cu/MWCNT/SiO₂ mono and hybrid nanofluid. Appl. Therm. Eng. 2024, 252, 123692. https://doi.org/10.1016/j.applthermaleng.2024.123692.
23.
Shi, X.; Li, S.; Wei, Y.; et al. Numerical investigation of laminar convective heat transfer and pressure drop of water-based Al₂O₃ nanofluids in a microchannel. Int. Commun. Heat Mass Transf. 2018, 90, 111–120. https://doi.org/10.1016/j.icheatmasstransfer.2017.11.007.
24.
Tumane, A.; Yewalikar, V.A.; Kubde, R.A.; et al. Experimental Analysis of Heat Transfer Enhancement of Car Radiator Using Cu Nanofluid with Base Fluid Water. Int. Res. J. Mod. Eng. Technol. Sci. 2023, 5, 3837–3846.
25.
Asokan, N.; Gunnasegaran, P.; Wanatasanappan, V. Experimental investigation on the thermal performance of compact heat exchanger and the rheological properties of low concentration mono and hybrid nanofluids containing Al₂O₃ and CuO nanoparticles. Therm. Sci. Eng. Prog. 2020, 20, 100727. https://doi.org/10.1016/j.tsep.2020.100727.
26.
Ramadhan, A.I.; Diniardi, E.; Basri, H.; et al. Experimental investigation of thermal conductivity of Al₂O₃-TiO₂-SiO₂ nanofluids in EG/water mixture for automotive radiator cooling system. In Proceedings of the 3RD International Conference of Bio-Based Economy for Application and Utility, Padang, Indonesia, 2023; Volume 2706, p. 020007. https://doi.org/10.1063/5.0120209.
27.
Arbak, A.; Attar, A.; Altikatoglu Yapaoz, M.; et al. Experimental investigation of bimetallic nanoparticles heat transfer characteristics in automotive radiators. Case Stud. Therm. Eng. 2023, 43, 102763. https://doi.org/10.1016/j.csite.2023.102763.
28.
Ukueje, W.E.; Abam, F.I.; Obi, A. A Perspective Review on Thermal Conductivity of Hybrid Nanofluids and Their Application in Automobile Radiator Cooling. J. Nanotechnol. 2022, 2022, 1–51. https://doi.org/10.1155/2022/2187932.
29.
Cardenas Contreras, E.M.; Bandarra Filho, E.P. Heat transfer performance of an automotive radiator with MWCNT nanofluid cooling in a high operating temperature range. Appl. Therm. Eng. 2022, 207, 118149. https://doi.org/10.1016/j.applthermaleng.2022.118149.
30.
Ramji, K.S.H.; Kumar, J.V.; Karthik, A.A. Experimental Investigation of Automobile radiator using Tungsten trioxide Nano-fluid. IOP Conf. Ser. Mater. Sci. Eng. 2020, 995, 012017. https://doi.org/10.1088/1757-899x/995/1/012017.
31.
Erkan, A.; Tüccar, G.; Tosun, E.; et al. Comparison of effects of nanofluid utilization (Al₂O₃, SiO₂, TiO₂) with reference water in automotive radiators on exergetic properties of diesel engines. SN Appl. Sci. 2021, 3, 1–13. https://doi.org/10.1007/s42452-021-04368-z.
32.
Vele, N.S.; Patil, R.K. Review on Heat Transfer Enhancement in Car Radiator Using Nanofluids. In Proceedings of the International Conference on Industrial Engineering and Operations Management, Bangkok, Thailand, 5–7 March 2019; pp. 527–537.
33.
Kanti, P.K.; Marulasiddeshi, H.B.; Said, N.M.; et al. Bayesian-optimized machine learning and experimental study of Al₂O₃-CuO hybrid nanofluid thermal performance in turbulent circular tube flow. Sci. Rep. 2025, 15, 38717. https://doi.org/10.1038/s41598-025-23785-3.
34.
Ajuka, L.O.; Ikumapayi, O.M.; Akinlabi, E.T. Entropy Generation of Graphene Nanoplatelets in Micro and Mini Channels: Nanofluid Flow in Automotive Cooling Applications. Int. J. Heat Technol. 2022, 40, 917–926. https://doi.org/10.18280/ijht.400408.
35.
Kanti, P.K.; Marulasiddeshi, H.B.; Said, N.M.; et al. Experimental investigation of solar collector efficiency enhancement using surfactant stabilized MWCNT and Al₂O₃ hybrid nanofluid. Sci. Rep. 2026, 16, 17354. https://doi.org/10.1038/s41598-026-42016-x.
36.
Choi, S.U.S.; Eastman, J.A. Enhancing Thermal Conductivity of Fluids with Nanoparticles. In Proceedings of the ASME International Mechanical Engineering Congress and Exposition, San Francisco, CA, USA, 12–17 November 1995, pp. 99–105. https://doi.org/10.1115/IMECE1995-0926.
37.
Razzaq, I.; Xinhua, W.; Rasool, G.; et al. Nanofluids for Advanced Applications: A Comprehensive Review on Preparation Methods, Properties, and Environmental Impact. ACS Omega 2025, 10, 5251–5282. https://doi.org/10.1021/acsomega.4c10143.
38.
Induranga, A.; Galpaya, C.; Vithanage, V.; et al. Nanofluids for Heat Transfer: Advances in Thermo-Physical Properties, Theoretical Insights, and Engineering Applications. Energies 2025, 18, 1935. https://doi.org/10.3390/en18081935.
39.
Nature Index. Nanofluid Heat Transfer Dynamics and Thermophysical Properties. Nature Index Topic Explorer, 2026. Available online: https://www.nature.com/nature-index/topics/l4/nanofluid-heat-transfer-dynamics-and-thermophysical-properties (accessed on 11 August 2026).
40.
Selvam, C.; Solaimalai Raja, R.; Mohan Lal, D.; et al. Overall heat transfer coefficient improvement of an automobile radiator with graphene based suspensions. Int. J. Heat Mass Transf. 2017, 115, 580–588. https://doi.org/10.1016/j.ijheatmasstransfer.2017.08.071.
41.
Prasanna Shankara, R.; Banapurmath, N.R.; D’Souza, A.; et al. An insight into the performance of radiator system using ethylene glycol-water based graphene oxide nanofluids. Alex. Eng. J. 2022, 61, 5155–5167. https://doi.org/10.1016/j.aej.2021.10.037.
42.
Abbas, F.; Ali, H.M.; Shaban, M.; et al. Towards convective heat transfer optimization in aluminum tube automotive radiators: Potential assessment of novel Fe₂O₃-TiO₂/water hybrid nanofluid. J. Taiwan Inst. Chem. Eng. 2021, 124, 424–436. https://doi.org/10.1016/j.jtice.2021.02.002.
43.
Li, X.; Wang, H.; Luo, B. The thermophysical properties and enhanced heat transfer performance of SiC-MWCNTs hybrid nanofluids for car radiator system. Colloids Surfaces A Physicochem. Eng. Asp. 2021, 612, 125968. https://doi.org/10.1016/j.colsurfa.2020.125968.
44.
Kumar, A.; Chand, P.; Hassan, M.A. Louvered finned car radiator with MWCNT-SiO₂ hybrid nanofluid: An experimental approach. Powder Technol. 2023, 415, 118176. https://doi.org/10.1016/j.powtec.2022.118176.
45.
Hassaan, A.M. An experimental investigation examining the usage of a hybrid nanofluid in an automobile radiator. Sci. Rep. 2024, 14, 27597. https://doi.org/10.1038/s41598-024-78631-9.
46.
Minh, C.N. Heat Transfer Enhancement Using Al₂O₃, CuO, and Hybrid Al₂O₃–CuO Nanofluids in Water and Ethylene Glycol–Water Mixtures in an Automotive Radiator. Int. J. Heat Technol. 2025, 43, 1429–1438. https://doi.org/10.18280/ijht.430420.

Scilight Press

Author Information

Abstract

Keywords

References

Discover

Flagship Journals

Support

Company